A few weeks ago, I took my DeLorean for its first drive of the year and I had a strange issue. When I would try to accelerate too quickly, the engine would bog down and just stutter instead of having a clean acceleration. I parked it for a few weeks thinking I'd look into it later.
I hosted a few local DeLorean owners at my place a few weeks later for a tech session, and this time I couldn't even get the car to start. It would crank, fire for a second or two, but would die every time. It would die immediately if I tried to give it any throttle. My suspicion was that it was doing the same thing as a couple of years ago and only running off of the cold start valve and none of the injectors were letting any gas through due to too low of fuel pressure from the pump.
I confirmed this by pulling one of the injectors and taking advantage of another set of eyes on the engine while I tried starting the car. To be sure, I jumpered the RMP relay and pressed down on the fuel meter and nothing came out of the injector. I suspected that the new ground for the inertia switch that I chose a couple of years ago to fix my fuel pressure issue wasn't good enough. At the time, a fellow owner had let me know that the placement of the ground I chose was not the best, which was a body mount bolt not too far from the gas pedal.
He recommended at the time that I instead run the ground wires to these bolts on the shifter:
During the tech session at my place, we worked on the other cars too and adjusted the mixture on 3 of the cars, including the idle on one car, and we troubleshooted my car. It was super helpful and fun to have 5 owners and 4 cars represented:
The next day, I ran new wires to the suggested grounds on the shifter and my car came to life again! It would bog down a little when I would push the throttle, so I also took a look at my mixture using a dwell meter. The diagnostic plug on my car was removed by a previous owner, so I had to hook up the lead wire on the dwell meter to this wire in the wiring panel on the right side of the engine bay:
I was getting just a steady reading of ~45 degrees on the dwell meter, which is what I was getting a while back when I tried setting the dwell, and I remembered that I bought a new O2 sensor a while back as that is the most common reason that the dwell doesn't swing when the car is up to temperature. The O2 sensor that I had in the car came with the new exhaust from DeLorean Industries. It didn't have any branding on it, but must have been bad from day one. I bought a new Bosch Oxygen Sensor 11051 from ebay for around $33 and I had it sitting around waiting to get installed for the last few months.
I swapped in the new Bosch O2 sensor and the dwell meter came to life once the car got up to temp again. My mixture was off, but I was able to get it to swing nicely in the right range after some adjustment. My throttle response returned without bogging down, and the first couple of drives I went on were flawless.
So if you ever have an issue where your car will fire for only a couple of seconds, you may have a fuel pressure problem like me, fixed by a better ground.
Just after the driving season of 2025, I took my car for a drive and discovered that the automatic radio antenna in the rear pontoon wasn't going down anymore and was stuck in the "up" position. I couldn't force it down either.
This antenna had lasted approximately 10 years as I last documented the replacement here in 2016. That doesn't sound too bad unless you know how little I have driven the car during that time. I'd be lucky if I put 1,000 miles on the car over that decade.
In searching for options, I found that the model I had was likely the best one that would work well in the car. I found that it was also available on Amazon for around $65, so I went with another Metra 44-PW22B
So out with the old, and in with the new, for the 3rd time in the 15 years that I've owned my DeLorean.
Since the antenna was stuck in the "up" position, I had to basically destroy it to get it to go down, which I was okay with.
I've gotten really good at putting in these antennas, but it is still a very unpleasant job as it requires very awkward positions and being bent over for long periods of time. The worst part is getting the right number of washers on the bracket so that the antenna is as straight as possible.
This new antenna seems to be a bit quieter than the previous model I installed, so let's see how long this new one will last!
As part of my DeLorean's interior overhaul, I chose to replace my car's headliner. I had replaced the headliner on the doors back in 2013, which I briefly mentioned in this post. At the time, the front and rear headliner in between the doors was still holding up fine and didn't need to be replaced. But both of those pieces had started to show their age and were starting to come loose in a couple of places. Also, the original backing material had started to lose its correct shape, so rather than messing with that fiber board material again, I bit the bullet and bought a new headliner set with fiberglass backing material.
I wasn't sure which color to go with on my car, but I contacted DMCH and they willingly sent me a swatch with color samples. I ordered the dark gray set and it soon arrived.
When I opened the package, I discovered that the color I was sent was much darker than what I had in the swatch, and sent the vendor an email with a picture of the new headliner with the two swatch colors I still had:
The swatch color on the left is what matched what I had in my car, and the light gray was for cars with light gray carpets. The folks at DMCH informed me that in the time between them sending me the color swatches and placing my order, their supplier discontinued the dark gray they were using and they had to switch to the next closest color.
I was super bummed as I was hoping to keep the original dark gray color I had, but I didn't love the lighter gray color either. I also didn't want to go through the hassle of a return, especially with such a large box that it came in. They tried to make it right and provided a 20% discount refunded back to me, which was good of them.
Removing the old headliner is pretty straightforward. The door headliners pop right out when you pry or pull on them. The center headliners require a bit more finesse. You have to remove the sun visors, held in by a couple of screws, remove the front interior courtesy light, remove the door weatherstripping where it holds on the headliner material, and then slide the whole headliner so that they are released from the bracket holding them in place. I made sure to document the correct wiring of the courtesy light so I'd be sure to hook it back up correctly:
My headliner left behind a bunch of glue residue where it meets the weatherstripping that I ended up scraping off with a razor blade. Here's what it looked like after I took out the headliner:
Once I got my headliner removed from inside the car, I was happy I chose to replace instead of simply recover them due to the state of the old backing material. Here's a look at the original backing material that is made of a type of fiber board:
Before I installed the new headliner, I found that one of the headliner screw brackets was extremely rusty, so I decided to drill out the rivets and refinish it by sandblasting and paint. Here is what I discovered it looked like before I removed it:
Here's how it turned out after refinishing it and putting it back in the car with new rivets:
Going back further in time, when I removed the sun visors for the first time, I also found that the metal brackets that the sun visors swivel around were pretty corroded as well, so I pulled them out to refinish them. I couldn't find any "before" pictures, but here they are in the process of being refinished and when I went to reinstall them into the sun visors:
One thing I was not aware of before I went to install the new headliner was what a pain in the butt it would be to get the sun visor screws to line up with the brackets. It took a lot of trial and error before I finally was able to get all four of them put back in.
The new fiberglass headliner comes with plenty of extra material around all of the edges, which allows you to make sure to get them installed just the right way. Here's a look at some of the extra material that I had poking around the weatherstripping as I was installing them:
The color of the new headliner doesn't match my sun visor color, but I think I'll be okay with that difference. The dark headliner doesn't feel nearly as dark as I thought it would when I first compared it to the color swatch. I love how the shape of the headliner has been fixed with the new fiberglass backing and I suspect that this will hold up for a very long time.
Years ago, I discovered that the strap that wraps around the tool kit and jack bag in the front of the trunk had hardened and was snapped in half. Upon further inspection, I found out that it was very crispy and would crack and break even more if I tried to bend it.
I set it aside for years, but then recently rediscovered it in a cupboard in the garage and I decided to see if I could find new material to remake it. After a bit of searching online, I came across some rubber strips that I could get in a size close to the original, without an adhesive on either side, and then cut it down length and width wise to get it to how I needed it. I found a roll on Amazon titled "Solid Rubber Strips 1/8 (.123)" Thick X 1" Wide X 10' Long. Here's a link that may or may not work in the future.
I bought them several months ago and decided to tackle this today. I first measured how wide the original strap was and cut the new rubber strip down to match that after seeing how much length I needed.
I then used pliers and a flat head screwdriver to remove the staple-like things holding the old ends together and used a small pick to put holes in the right places on the new rubber strip before swapping them over.
I then used a hole punch for a hole in the middle for the retaining bracket to attach to it. It all came together nicely.
Here it is all done, then installed in the car. It wasn't a hard or long job, but I just never made it a priority to take care of it. On to the next project.
A while back, I had to kneel on the driver's seat to access something in the car when I felt the seat "give" a little. I believe that's the moment that the rubber mat under the seat tore, which made it feel like the seat bottom didn't have much padding and made the seat quite uncomfortable. Here's what that looks like:
I attempted a repair myself by finding some nylon material at JOANN Crafts, and put that in place to better support my backside. So I took out the broken rubber material:
The material needed to be strong enough to support my body weight, but hopefully also have a little give to it like the original rubber. The material I found was the kind of webbed material that you might find on patio furniture, which meant that it would be durable and strong, but it had zero give. This was the final result:
It was better than the broken rubber mat, but it just didn't feel as good as before. I ran it this way for a couple of years, but when I underwent an overhaul of the car's interior, I thought I'd attempt a better repair by having a local upholstery shop see what they could do.
They were unable to find a similar material to the rubber that was original, so we settled for another material that seemed to have a little bit of give to it. I haven't gotten the interior back together to see how it feels, but I'm hopeful that it will be a better solution to my temporary fix. It sure looks a lot prettier, even though I'm the only person that will ever see this side of the seat:
My DeLorean's A/C hasn't worked since I bought it. All of the original R12 had leaked out by the time I came to own it in 2011. A couple of years after I bought it, I flushed out the original system w/ mineral spirits and converted the fittings over to R134a. I had working A/C for a very short driving season that year before all of the refrigerant leaked out. I added some leak dye on the next refrigerant fill up, but even then, I couldn't ever find the source of the leak. I also suspected a problem with the original compressor at the time and replaced it with a new unit.
I concluded that the original A/C hoses were likely allowing the refrigerant to seep out, or I had a potential problem with the evaporator in the A/C housing. I knew that at some point, I would need to overhaul my entire system if I wanted reliable A/C.
Earlier this year, I dove into a project on the interior of my DeLorean that involved removing much of the interior, including the dashboard, and I thought that if I was going into it this deeply, now would be the best time to remove the A/C unit housing and include that as part of the interior overhaul. While doing that, I should replace the A/C lines with a modern replacement, the cooling fans, the evaporator, condenser, and everything else on the system, minus the new A/C compressor.
My engine cooling system was in great shape with the exception of the radiator of unknown age. I had replaced all of the cooling hoses and pipes a few years ago, including a new water pump, and the radiator was the only unsure thing remaining. I didn't know if it was the original radiator or if it had been replaced by a previous owner at some point. I decided that I didn't want to dive into the front end again like this for a radiator replacement, so I thought it best to replace it as well.
I already wrote extensively about the A/C unit housing restoration, which you can find here. The rest of the A/C overhaul was pretty straightforward. The condenser came out with the radiator. Here are some photos of that during the process:
The hose connections on the condenser came off much easier when it was lowered and more accessible with a large wrench. There was quite a bit of nasty brown fluid that came out of the hoses and the condenser once I had them disconnected.
While I was in there, I chose to replace my original cooling fans with modern replacements. Might as well, right? A little before and after action:
These fans mounted right into the original mounting holes on the fan shroud, which in turn mounted right up to the new radiator.
Getting the accumlator/dryer out was definitely the hardest part of the whole job. As anyone that has looked at the A/C dryer, there is little room to work. I couldn't get the connection loose coming from the evaporator to the dryer and didn't want to hack up the fiberglass underbody in order to create more space, so I whipped out the Sawzall and cut off the connection on the dryer in order to free it up. Even with the dryer out of the way, that connection took a lot of force to finally come free.
I then moved to the A/C lines and chose to route the new lines the same way the original lines were ran. I cut off the hoses near the compressor, taped the end of the old line to the new line, then fished the old lines out while the new lines but pulled into place.
The new lines were from DeLorean Industries and don't come with any connections pre-installed, which makes it easier to fish the new lines in between the underbody and frame. The kit uses a clamping system that I had to watch a video on YouTube in order to figure out, but seems really solid. I really like how the hoses are longer than needed and you trim them down to length, which provides extra flexibility for any changes in the routing.
I routed the line near the steering shaft further up to avoid any rubbing as the steering shaft rotates around. This route seemed like the best option to avoid future problems:
The only issue I encountered with all of the new parts was with the new condenser. One of the four nuts on the mounting bolts was stripped and wouldn't come off so I could connect it to the radiator. I contacted the vendor (DMCH) and they promptly sent me a new mount at no charge, which fixed the issue after I swapped the parts.
Winter is setting in now, so I won't have a chance to charge the all-new A/C system until next year. I'm sure there's a fitting or connection somewhere that I'll need to snug down, but everything is back together. I did get the car running so I could burp the new radiator and all of that is also back together and working great so far. The new fans also came on when the car got up to temp. They sound surprisingly quiet compared to the original fans. I also made sure that they were wired up correctly to pull air instead of pushing air back towards the radiator, which other owners have mistakenly done before. All checked out there and I fully expect to have many uneventful heating and cooling years ahead with this huge and pricey overhaul.
Speaking of price, here's a rough rundown of what some of the key items cost in 2024:
I replaced the radiator in my DeLorean as a "while I'm in there" thing, but noticed that the original fan shroud had a decent sized crack on the bottom where the A/C line runs into the bottom of the condenser:
Rather than replacing it with a reproduction, I decided to attempt a repair using a plastic welder, which was a new concept to me. Here's a link to the plastic welder that I purchased. When you insert a metal staple-looking thing in the rods, then pull the trigger, it quickly heats up the metal staple and it melts itself into the plastic. After it cools, the plastic hardens around the staple and it holds it firmly. It's really a great concept.
I added several of these plastic welding staples on the backside of the fan shroud, and after I installed the new radiator, I put in the repaired shroud. I am extremely pleased at how well it turned out:
Several years ago, in a project that started with a simple desire to change the old and failed motor mounts that evolved into pulling the motor and transmission, I also installed a modern fuel pump from DeLorean Industries so that I would have as reliable of a car as possible. During this process, I dropped the fuel tank for a deep cleaning, both inside and out, which I have written about before.
I have recently had my car off the road for a year while I tackled another project that snowballed, but this time it was for many things on the interior. I recently got it put back together enough to try and fire it up. It had been much too long since I had heard the motor come to life and I was excited to reach that milestone once again.
When I went to start it, it would fire immediately, but wouldn't stay running. It would cough, stumble, then die within a few seconds. I had a similar symptom as this a year and a half ago and felt like a fool when I discovered that it was just about empty on gas. I had to calibrate the fuel sender so it was more accurate, but that's a story for another time.
So I checked the fuel level, which was easy because I still had the fuel pump access panel off from when I had replaced the A/C lines, which I'll write about another time. I simply popped off the cap where the original fuel sender used to be and I could see that the tank had plenty of fuel with it being around half full.
It was acting like it would run when the cold start injector would kick on, but then not get any more fuel and die. To be sure it wasn't electrical, I verified the ballast resistor and coil were all wired correctly and that nothing was loose. Once that all checked out, I decided to dive further into the fuel. I decided I needed to verify that fuel was making it to the cylinders, so I pulled all six injectors and put them in glass mason jars.
On a Delorean, you can jumper the RPM relay so that the fuel pump runs nonstop, which is great for testing while the car is off. If you have the fuel pump running, you can then press down on the metering plate, and if everything is working, you should get fuel spraying from the injectors. I jumpered the RPM relay, but when I pressed down on the metering plate, I had zero fuel from all six injectors. I was stumped.
I removed one of the injectors and repeated the exercise just to see if fuel would come out without an injector in the way, and I did get fuel, so I knew the fuel pump was at least providing some pressure. Here's what that looked like:
I suspected that there may not be enough fuel pressure to open the injectors, but I didn't have a K-Jet fuel pressure gauge. I reached out to some local owners, and was lucky to have one volunteer to loan me their pressure gauge set. Once I got my hands on that, I saw that I only was seeing 40 PSI at the lines at the rear of the car.
In case anyone needs any reference photos, here's how I hooked up the pressure gauge near the motor:
In order for the injectors in a DeLorean to open, they need to get ~50 PSI, and since mine was only pushing 40 PSI, it made sense as to why I wasn't getting fuel out of my injectors. I needed to determine if the low pressure was being caused by something in between the pump and the lines, or if it was the fuel pump. There was another fuel pressure kit in the parts I borrowed that allowed me to hook a gauge up directly coming off the pump, so I disconnected the feed line, put on the pressure gauge, and was surprised to see ~40 PSI coming right off the pump.
Some other owners suggested that low pressure could be caused by a low battery, so I made sure the battery was charged, then checked the voltage at the connection. It registered right where I needed it to be, at around 12.7V, but I was still only getting 40 PSI from the pump when I jumpered the RPM relay.
I decided to bypass all of the wiring harness and see what happened if I hooked the fuel pump directly up to the battery instead of via the wiring harness. To my surprise, the pressure jumped up to ~60 PSI, which meant that something in the wiring was causing the low pressure.
After much head scratching, I couldn't figure out why I would have lower pressure from the fuel pump when the wiring harness was showing 12.7V, but with the same battery, pressure would jump up to normal if I hooked it directly to the battery. Someone suggested that I could be experiencing a drop in voltage once there was a load on the wires. I picked up a kit to backprobe the wires so I could watch the voltage when the fuel pump was hooked up to the wiring harness, and sure enough, as soon as power was sent to the fuel pump, the voltage dropped to only about 9 volts. The next question was why this was happening.
Some helpful DeLorean owners suggested that the wires were corroded, burned from heat, or there was a bad connection further up the harness, like where the wiring is connected near the windshield washer reservoir. The wiring harness looked good near the fuel pump. The wires were still very flexible and not at all crusty.
I saw no evidence of corrosion on the connector, so I decided to go upstream and check the connection near the washer fluid reservoir. I just wrote a blog post about the headache of getting the reservoir cover off as I had several bolts that spun the rivnuts.
I did eventually get that taken care of and found the wire on the connection that supplied power to the fuel pump. Here's the connector near the washer fluid reservoir:
I removed the fuel pump, put it in a bucket of gas, and hooked it up directly to the connection that supplied power, and to my surprise, I still saw a big drop in voltage and the fuel pressure was not as high as hooking it directly up to a battery. That meant that something further up the line was causing a voltage drop. You can see the voltage dropping in a video I took during all of my testing:
I then stumbled upon a write-up during all of my head scratching that the ground may need some attention. The ground for the fuel pump is tied to the inertia switch, which makes sense as the inertia switch would kill power to the fuel pump in the event of a collision. The inertia switch is located near the clutch pedal inside the car. Visually, mine looked fine, but I thought that I didn't have anything to lose.
The process of adding a more reliable ground involves cutting the ground wire coming off of the inertia switch, then running a new ground wire from both ends of the cut wire, under the carpet, and to one of the bolts that holds the tub to the frame. I followed the process that I found outlined here. I then tested the fuel pump pressure using the wiring harness and was so pleased to see it shoot up to nearly 70 PSI. The problem this entire time was a weak ground. I'm glad it wasn't a bad fuel pump or a cooked connection, but it was still frustrating that something I hadn't touched or messed with created this problem.
Next, I needed to confirm that the fixed fuel pressure would result in fuel coming out of the injectors, so back to the mason jars I went.
I was extremely happy when I pressed on the mixture plate and heard the whistling of fuel coming out of the injectors.
I was getting a pretty inconsistent spray pattern and volume from some of them, so I swapped some around to see if the problem followed the injectors. I decided that they could all use a good cleaning, so I took them all out. The injector seals were a pain to get off as the rubber was super hard and inflexible. I figured I might as well replace those while I had the injectors out. I found replacements from Advanced Auto for $2 a piece and they arrived within just a couple of days, which was awesome.
I put all of the injectors into a bucket of Berryman B-12 and was blown away with the amount of gunk that came off the injectors. They went in looking quite nasty and came out looking brand new after less than 30 minutes. But I knew that what I really needed to do was to force cleaner through the injector with pressure. I don't have a K-Jet injector cleaner and didn't want to wait around for one, so I created a redneck way to get cleaner through them by using an air compressor fitting, some foam to create a seal around the injector, and I was successful in getting a little bit of cleaner at a time through all of the injectors. I then connected the injectors back up to the fuel lines and tested the spray patterns and volume.
As you can see below, volume was a little bit of a hot mess. I swapped some injectors around and did several rounds of testing and saw a little improvement.
Ultimately, I took out a couple of injectors and put them through another round of cleaning. I had previously heard that a good rule of thumb is to get 5oz of gas out of each injector by pressing the mixture plate down for 30 seconds. I marked 5oz on the far-right bottle and tested to see where things ended up. It wasn't too far off of that number, so I called it good and installed the injectors back into the engine.
Here is one of the new injector seals before putting the injectors back in the engine. Check out how nice and clean the injector looks:
After putting in all the injectors, the moment of truth came when I went to start the car. It started and ran for the first time in a year after stumbling for a bit at first. I blew out all of the cobwebs and it ran beautifully. I got it up to temp while I got air out of the new radiator that I had installed during the year's nap and now I need to wrap up the rest of the interior before I can get it back on the road.
Here are some clips of the car running once again. I'm so pleased to have gotten past this no start headache.